• Skid Plate - All 1/4" Plate Steel
• Hi-Lift or Farm Jack Mounting Holes
• Recover Point
• Step For Your Roof Rack
• Dual Bottle Openers
• CB or HAM Antenna Mounting Holes
• CB Antenna Mounting Kit (Optional)
• Wheel Chock
• Back-Up Trail Camera (Optional)
• Trail Flag Mounting Holes
• 1-1/4" Accessories Receiver
• Bike Rack (Optional)
• Fishing Pole Holder
• Adjustable Depth Setting

FAQ

1) Will your trailer hitch skid plate fit my truck?

Our skid plate was specifically designed to fit most Jeep's, Truck's and SUV's. But, with so many variations in receiver hitches, it's impossible to accommodate all vehicles.

2) What size hitch receiver do I need?

Our skid plate is designed to work with a 2 inch or 2-1/2 inch receiver.  For a 2-1/2 inch receiver, you'll need a standard reducer sleeve 2-1/2 inch to 2 inch.  You can find reducer sleeves at local or on-line hitch outlets.

3) How wide is the skid plate?

It's 12 inches wide.  This gives significant protection to your vehicle but limits lateral stresses on your hitch receiver.

4) Is the skid plate removable?

Yes, just pull the pin and the skid plate slides right out.

5) Is your skid plate made for off-road use?

Yes, our skid plate is 1/4" plate steel and designed specifically for off-road use.  

6) What does the skid plate protect?

Our skid plate is designed to help protect any part above the skid.  Examples include - your safety chain rings, bumper, back-up sensors, spare tire, exhaust and more. Obviously, each vehicles protection will differ.  We guarantee our skid plate for quality and workmanship.

7) What are all the holes for?

The top two (1/2" holes) are for the jack mount bolts, CB or HAM radio antenna, or for a trail flag.  The rectangle hole in the center of the skid plate is for our optional back-up trail camera or for any 1-1/4" hitch receiver accessory (like a bike rack, luggage carrier, etc.).  The six other holes are for accessory add ons, or for grounding some antenna's.  

8) Will this fit all Hi-Lift or Farm Jacks? 

As far as we know, yes.  The bolts we supply with out kit are 1/2" bolts and the slot allows you to adjust one end to fit any farm jack.

9) Are the bottle openers upside-down? 

No, they just look that way.  

10) Will the CB antenna hit my rear door?

Probably!  Just buy a quick disconnecter or tilting adapter from any CB shop.  Or, you can easily unscrew the antenna from the base.

11) Why don't you sell more CB gear?

At this point, we just wanted to make sure it was easy for our customer to be able to mount the antenna. The FireRing coax guarantees a good connection and is easy to install. The typically PL259 connector is too bulky to fit under the bend of our skid plate.

12) Why is my CB not working?

We're not a CB shop, but all CB's need good connections and the antenna's need tuned with an SWR meter.  SWR meters are pretty cheap and easy to use.

13) Can you disconnect the CB coax at the skid plate?

You can either remove the base bolt or install a coax quick disconnect fitting.  You can also visit a CB shop, found at most large truck stops.

14) Is the skid plate bent or welded at the angles?

Each skid plate is bent with a 127 ton press brake to maintain maximum strength at the most common ground impact point.  The skid plate is then MIG welded to the 2 x 2 inch shaft and reinforcement brackets.

15) Is the skid plate powder coated or painted?

Powder coated.

16) Will the skid plate bend?

It's unlikely, but with a significant impact, even thick steel can bend.  Mine has been on the the extreme trails in Moab, Utah and in Ouray, Colorado with nothing more than scrapes.  The bottom plate is designed redundantly to stop if it's bent up against the receiver.

17) Does the leading edge plow?

No, the leading edge of the skid plate sits significantly higher than your differential (rear end) preventing plowing. Obviously, there's an exception, if you bury your 4x4 in deep mud.  In that case, remove the skid plate before going mudding.

20) Will the CB or HAM Antenna clear my rear tire?

This all depends on your hitch receiver and tire.  All hitch receivers are slightly different, with different distances from the rear bumper and differing hole depths. If you have a huge rear tire or equipment mounted behind the rear tire, there might not be clearance for the antenna whip.

21) Can I buy my own hardware or camera?

Sure!